Jump to content

[Tutorial] How 2 flash ur Nokia S40 BB5 phone with J.A.F by lrajesh555


LRajesh555

Recommended Posts

Here is a tutorial to flash ur nokia s40 phone with original firmware files using J.A.F.

Download JAFSetup_1.98.62.rar : http://www.mediafire.com/?yn1ywy5cunj

Downalod and install Nokia PC Suite : http://europe.nokia.com/support/product-support/pc-suites

Download Navifirm from the attachment

Install JAF setup.

Here I m taking Nokia 2700c for flashing.

Required files for flashing purpose are shown as the figure below:

http://forum.gizmolord.com/index.php?action=dlattach;topic=2062.0;attach=4365;image

Now come to the procedure for downloading your firmware files

1. open navifirm.

2. select ur RM-Type in the 1st column. To know ur phone's RM-Type, dial *#0000# in ur phone and note the RM-type and ur firmware version too.

    (for my 2700c, its RM-561)

3. select ur firmware version in the 2nd column

    NOTE: Don't select any lower firmware version. U may select any higher version but never downgrade. By Downgrading u will get a bricked phone. 

4. select the variant in the 3rd column according to ur phone's product code. To know the product code, just open the battery and u will see the RM-type and the product code.

    (As u can see mine product code is 0588814)

5. In the 4th i.e filelist column u'll see 6 0r 7 files but u have to download the ".mcusw", ".ppm" & ".image" these 3 files.

http://forum.gizmolord.com/index.php?action=dlattach;topic=2062.0;attach=4367;image

6. click on 'add to download task' then select the folder where u want to save them. then click download.

http://forum.gizmolord.com/index.php?action=dlattach;topic=2062.0;attach=4369;image

7. ur downloading will b started.

http://forum.gizmolord.com/index.php?action=dlattach;topic=2062.0;attach=4371;image

8. now just rename the .mcusw file to .c0r (c-zero-r not c-o-r)

    refer the picture below as i have renamed it.

http://forum.gizmolord.com/index.php?action=dlattach;topic=2062.0;attach=4373;image

http://forum.gizmolord.com/index.php?action=dlattach;topic=2062.0;attach=4375;image

Now the procedure for flashing ur phone

1. connect ur phone with pc via usb cable in pc suite mode.(phone should be fully charged)

2. Run Pkey emulator as administrator [For Windows 7 users: right click Pkey emulator >> Properties >> navigate to compatibility Tab >> tick "run this program in compatibility mode for: (Windows XP service Pack 3)]

3. ur jaf will open as the picture below. then click on 'go'. u will get box driver error, press ok.

http://forum.gizmolord.com/index.php?action=dlattach;topic=2062.0;attach=4377;image

http://forum.gizmolord.com/index.php?action=dlattach;topic=2062.0;attach=4379;image

4. then go to 'bb5' tab and u ll see like this picture below

http://forum.gizmolord.com/index.php?action=dlattach;topic=2062.0;attach=4381;image

5. then check "manual flash", "dead usb"...."normal mode" & "crt 308" are already checked so no need to check them again. And see ur jaf is looking exactly like the below picture.

EDIT: Uncheck the CRT 308 and see ur jaf exactly looks like this:

http://forum.gizmolord.com/index.php?action=dlattach;topic=2062.0;attach=4399;image

6. click on MCU button and select the .c0r file from ur firmware files' downloaded folder.

http://forum.gizmolord.com/index.php?action=dlattach;topic=2062.0;attach=4385;image

http://forum.gizmolord.com/index.php?action=dlattach;topic=2062.0;attach=4387;image

7. click on PPM button and select the .ppm file.

http://forum.gizmolord.com/index.php?action=dlattach;topic=2062.0;attach=4389;image

8. click on CNT button and select .image file.

http://forum.gizmolord.com/index.php?action=dlattach;topic=2062.0;attach=4391;image

9. now see the MCU, PPM & CNT buttons r glowing green as shown in the picture below.

http://forum.gizmolord.com/index.php?action=dlattach;topic=2062.0;attach=4393;image

10. now switch off ur phone and disable ur PC suite or uninstall it.

11. click on FLASH. U will get a warning message. Press yes.

http://forum.gizmolord.com/index.php?action=dlattach;topic=2062.0;attach=4395;image

12. And after that jaf will search for phone and will ask to power on ur phone. Immediately press ur phone's switch on button until it is recognized. It ll take maximum 2-3 seconds for ur phone to b recognized. So don't hold ur power button. Just press for 2-3 seconds and leave it when u hear the sound.

13. ur flashing will start.

14. wait for 3-4 minutes.

15. u will hear a sound when it says DONE.

Flash sucessful.

Happy Flashing. :):):)

Post updated with one correction : Uncheck the 'CRT 308'

Hit the green arrow if i helped u.:P:)

post-1907-138186175086_thumb.png

post-1907-138186175096_thumb.png

post-1907-138186175104_thumb.png

post-1907-138186175113_thumb.png

post-1907-138186175123_thumb.png

post-1907-138186175131_thumb.png

post-1907-138186175141_thumb.png

post-1907-13818617515_thumb.png

post-1907-138186175167_thumb.png

post-1907-138186175174_thumb.png

post-1907-138186175184_thumb.png

post-1907-138186175192_thumb.png

post-1907-1381861752_thumb.png

post-1907-138186175209_thumb.png

post-1907-138186175217_thumb.png

4397_.rar

post-1907-138186175252_thumb.png

Link to comment
Share on other sites

Wow, thatz something an awesome work :) Great tutorial..pretty well explained :-bd Topic marked Sticky +5 Some corrections: CRT 308 should be marked untick You can even copy paste the firmware files to C:\Program Files\Nokia\Phoenix\Products\RM-XXX (where XXX will be the RM number) Then select "use INI" and choose the phone model from the popup box...The firmware files will be auto-selected :)

Link to comment
Share on other sites

Wow, thatz something an awesome work :)

Great tutorial..pretty well explained :-bd

Topic marked Sticky

+5

Some corrections: CRT 308 should be marked untick

You can even copy paste the firmware files to C:\Program Files\Nokia\Phoenix\Products\RM-XXX

(where XXX will be the RM number)

Then select "use INI" and choose the phone model from the popup box...The firmware files will be auto-selected :)

thanx for the +5 and for the correction.:)

But there z no problem in flashing when the 'crt 308' is checked.

And we can use the 'use ini' too by copying all the firmware files to c/program files/nokia/phoenix/rm-xxx :):)

thanx :)

Link to comment
Share on other sites

i m downloading ur link files now tell me 1 thing my current software version is RM-364 v 12.35 i can use this files on my current version???can i get hindi language support in this files???

Yes, Its an Indian firmware (original)....so it should have hindi language support in it !!!

just flash with it...if it bricks or not working for you, then flash with the one u used before (v12.35)

Link to comment
Share on other sites

  • 2 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
×
  • Create New...